The holder without which even a new valve seal won't seal
In a valve, it is not the seal alone that seals, but the interplay of seat, seal and holder. The holder guides the seal, keeps it centred and presses it evenly onto the seat. If it wears in, becomes bent or gets an edge worn into it, the seal sits crooked – and a crooked seal won't hold, even straight from the factory.
That's why, when a valve keeps dripping after the seal has been replaced, the holder is the next thing to check. This item carries part number A.1.004.01.
When it's due
The valve keeps dripping even though the seal is new. After a short time, the new seal shows a one-sided impression. The holder has a visible groove, a pressure mark or a worn-in edge. It has become hard to move. Or you have the valve open anyway – then the holder is one of the parts worth checking at the same time.
At a glance
| Type |
Holder for the valve seal |
| Installation location |
in the valve, between seal and shaft. The documentation does not specify a particular valve. |
| Compatible with |
The documentation does not name a machine. Send us the serial number and we'll check the fit. |
| Scope of delivery |
one holder. The seal itself is not included. |
| Part number |
A.1.004.01 |
| Specification |
We have no documentation on material and dimensions. |
| Installation |
Installation by a qualified technician recommended |
| Brand |
La Marzocco |
Important for installation
The part sits in a pressurised valve. Only work on the machine when it is switched off, cooled down and depressurised. When dismantling, also check the valve seat: a new seal on a worn-in seat won't hold, no matter how good the holder is. We deliberately do not provide step-by-step instructions here.
Who it's for
For workshops that repair a valve rather than replace it completely, and for anyone looking for exactly this part using the number A.1.004.01 from a service document.
What goes with it
Related parts include the stainless steel valve seat F.3.007, the steam valve seal unit B.2.010 and the steam valve shaft spring. More valve parts can be found in the Original spare parts section, the rest of the range under La Marzocco accessories and spare parts.
From our workshop
When a valve at our place in Bern or Zurich drips for the second time within a year, we don't change the seal again but take a close look at the holder and seat instead – in nine out of ten cases, that's where the problem lies. This is our routine, not a manufacturer's specification. What's in the cup while we work: Nutty Delight, Cozy Chocolate or Very Nutty. More under Coffee beans.
No returns
Original spare parts are excluded from exchange and return. They are sourced specifically for each order and cannot be resold once they have been installed or test-fitted on a machine. So before ordering, check the model, year of manufacture and serial number of your machine – or drop us a quick message and we'll check the fit together. Your rights in the case of defective goods remain unaffected.
Frequently asked questions
Is the seal included?
No. Only the holder is supplied. The seal is a separate item – let us know which valve you're working on and we'll find it for you.
Which valve does the holder belong to?
Our documentation doesn't say, so we don't claim anything. What is reliable is the number A.1.004.01. Send us your machine's serial number and we'll check the fit.
What material is it made of?
We have no information on this, so we don't state one.
My valve keeps dripping after changing the seal – is it the holder?
It could be. But often the valve seat is the cause. Both parts should be checked together when troubleshooting.
Can I see the part in your shop?
Our showrooms in Bern (Gerberngasse 44) and Zurich (Hagenholzstrasse 50b) show a wide selection, but not our entire range – the display changes. Drop us a quick line at [email protected] before your visit, and we will check whether the product you have in mind is currently there.
Questions about compatibility? Write to us at [email protected]. We deliver across Switzerland and to Liechtenstein in 2-4 working days.
